Presented here down the page you can locate a good deal of amazing ideas around Installing A Bathtub.
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old bath tub with a new one is likewise a reasonably challenging task. If the old bathtub is readily easily accessible, the task can move speedily; if you have to open up a wall surface to eliminate the old tub and also place the new bathtub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will need an assistant to leave the old tub and also embeded in the new one. Make sure you have actually qualified yourself for the work and are comfortable attempting it. As opposed to working with a contractor to take over a halfway-completed project, it is better to think about using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already acquired a brand-new tub and don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist ought to make up the following:
Preparing for the Installation
To start with, the supporting frame provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be rather troublesome because of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Making use of both wood boards under its feet, put the bathtub in the required placement. The wooden boards are handy in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub till the level reviews level.
To install taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water and examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the bath tub as well as also examine the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling and also securing around the bathtub must wait until the bath tub has been made use of a minimum of when as this will settle it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in area between the tap and also the sink. Secure the faucet in place with the supplier provided backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, causing the water to permeate the wall in between the bath and also the tiling, causing complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can crack fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our post about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for taking a few minutes to read through our article post. Loved our piece? Please share it. Let other people locate it. Thanks for your time spent reading it.
Book Your Service